It is very possible that a trailer hitch receiver for a 1966 Chevrolet C/K 10 short bed will work on your 1966 Chevrolet P10 Panel Truck but you will want to measure the width of your frame to confirm this.
The Curt Trailer Hitch Receiver # 13028 is confirmed to fit a 1966 C/K 10 with the short or long bed, and fits frames that are 34" wide measured outside to outside.
As long as this matches your frame width this would be a great option for you.
I included a link to the written instructions... view full answer...
For your 1997 Chevy C/K 2500 8 foot bed, there are many different rail kits and 5th wheel hitches that are compatible.
The Husky Custom Base Rails and Installation Kit for 5th Wheel Trailer Hitches # HT31402-686 you referenced is a confirmed fit. These rails can work with many different industry standard size hitches for your 5th wheel trailer. The Husky Silver Series 16K S 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs # HT31313-31314 will fit that criteria and will be a good... view full answer...
I have a solution for you but the Curt item # C60652 will not fit your 1993 Chevrolet C/K Series truck. Instead you will want the Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit item # C60713. This kit fits both the 6-1/2' and 8' bed models not the cab and chassis model. view full answer...
You can usefully change your trailer tires to a higher load rating if the trailer's capacity is high enough to make that change worthwhile. If your trailer axle and hubs are rated for a higher load capacity than the two tires then moving to a higher load rating tire/wheel will let you realize a gain in overall weight capability. However, upgrading one part of the system does not automatically mean that you have increased the trailer's capacity; the lowest-rated part of the system - the... view full answer...
It depends on the bedliner, if it is a spray on bedliner then it should not be a problem at all. If it is a slide in bed liner it most likely cause a fit issue, but you have an option.
What you could do is get the bed mat recommended for the vehicles and then trim the mat so that it fits around the bed liner. view full answer...
The highest capacity trailer hitch that we carry for your 1986 Chevrolet K3500 with an 8 ft bed is the Draw-Tite Ultra Frame Trailer Hitch, # 41947. The Titan trailer hitch # DT45519 that you referenced is designed to fit some GM trucks from 2001 to 2010 and will not fit on your truck.
The Draw-Tite Ultra Frame trailer hitch is a class V hitch with a 15,000 lbs gross trailer weight capacity and a 1,500 tongue weight capacity. Those capacities increase to 16,000 lbs and 1,600 lbs when... view full answer...
I spoke with my contact at Derale and he said that yes, you can use an oil filter relocation kit such as # D15718 with a diesel motor. The only thing that matters is the thread size that the motor requires for a filter. This particular kit fits engine threads that are 20mm x 1.5. If your motor takes a different thread size let me know. And if it takes a cartridge filter then there isn't a relocation kit that will work. view full answer...
Yes, the Westin Fey Diamondstep Rear Bumper with Custom Installation Kit part # 21000-92230 is correct for a 1998 Chevrolet C/K Series Pickup. This combo is a direct bolt-on fit so no drilling will be required and it is a direct replacement for the factory rear bumper. view full answer...
Installing a Dexter Predator DX2 Trailer Brake Controller # 58-8 in a 1993 Chevy Silverado and 1994 Chevy Cheyenne, both of which are Chevy C/K Series pickup trucks, require both trucks to have their own 4-flat connectors and a brake controller wiring kit. However, since both trucks require the Predator to be hardwired, it would mean you would have to get two brake controllers or you would need to wire and un-wire the controller to change trucks; there are better options that will allow... view full answer...
Thanks for your interest in the Advent # ADV94FR Rooftop RV Air Conditioner. The thermostat is not wireless. It has 4 wires that are short as this thermostat is a replacement thermostat that just connects where the previous thermostat was located.
A similar RV A/C that may interest you is the Atwood # AT15033-22 which has a wall thermostat like the Advent, but also features a remote control that lets you adjust the temperature, fan, and power. Also includes a heat pump for chilly nights.
I... view full answer...
The Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947 is designed to fit the pickup versions of the 1977 Chevy C/K Series truck. Since you have the cab and chassis version you need to use the Curt Class IV Trailer Hitch Receiver # C14082 instead which fits as long as your frame is 34" wide outside to outside.
This does require drilling for the installation but it is confirmed to fit your cab and chassis (as long as the frame width is correct as mentioned above). I'm not sure if the... view full answer...
I can help you narrow this down further, but the AA204038 only fits 1500 series 2WD models so that won't fit your truck. The K20 would be the equivalent of the 2500 series so you need one of the following based on your bed length:
-Aries Round Nerf Bars # AA204040 (6-1/2' bed)
-Aries Round Nerf Bars # AA204041 (8' bed)
I also spoke with Aries and they said the saddle tanks won't interfere with the nerf bar installation. view full answer...
The Westin Bumper # 76001 is only fitted from 1967 models to new. The similar # 21007-92500 is the fit for 1967-1972 model years. I am sure you could make either option work for your truck, but there are not custom brackets. Installation will require customization and the weight ratings will not hold true since they are based on the custom installation brackets when tested.
Unfortunately we don't have a simple custom fit for your truck. view full answer...
I have another option but the Curt Trailer Hitch Receiver # 13942 will not fit on your 1992 Chevrolet CK 1500 if you do not have a roll pan.
This is due to the fact that the roll pan hitches sit higher up and require a cut out in the roll pan for the hitch. With your standard bumper the hitch would be behind the bumper instead of under it.
As long as you have a standard rear bumper I recommend the Curt Trailer Hitch Receiver # C13042 which will put the receiver tube under the bumper,... view full answer...
Yes, the B&W Gooseneck Hitch, # BWGNRK1050, will fit on your 1991 Chevrolet K2500 pick up with a 6-1/2 ft bed and 6 lug wheels as long as it does not have a flareside/stepside bed.
The brackets with this hitch do not require any drilling into the truck frame for installation and this hitch is rated for 30,000 lbs. Before towing a gooseneck trailer using this hitch and your truck you should check the towing capacities of your truck. view full answer...
I reached out to my contact at Carr for you. The Carr Deluxe Light Mounting Bar - Black Powder Coated Steel, # CARR210341 is rated for up to a 50 inch light bar. They said it may fit, but they have only rated it for 50 inch applications. view full answer...
From the information I was able to obtain, the item you selected, MagnaFlow Stainless Steel Catalytic Converter, part # MF23453, will fit your 1997 Chevrolet C/K Series with 5.7 liter motor.
The # MF23453 Catalytic Converter is 49-State legal, and is legal in the state of Virginia. This catalytic converter is not legal in the state of California. view full answer...
GM didn't start putting the under-dash tow package connector in their trucks until the 1999 model year, so in order to install a controller on your 1997 C/K pickup, you'll need to hard wire it using our Brake Controller Install Kit, part # ETBC7. If your truck doesn't already have one, a functioning 4-pole trailer connector needs to be installed using part # 118315.
The Tekonsha Primus, part # TK90160 is a good, basic proportional brake controller. A proportional controller will provide... view full answer...
The Curt # C61301 fits 2012-2019 Chevy 3/4 and 1 ton pickups, and wouldn't work for your 1995 K2500. If you're looking for an Overbed folding gooseneck hitch, I'd recommend the Curt # C61504-52, which includes the appropriate install bracket kit for your truck. If you needed the bracket kit only, that would be part # C61504
If you'd like to install a 7-way trailer connector in your truck bed, you can do so using part # 20023. view full answer...
Go To Results